Skip to main content Skip to search Skip to main navigation

Epson Accelerometer M-A352AD10 UART/SPI

Epson Accelerometer M-A352AD10 UART/SPI

Available in the shopStructural health monitoring

A 3-axis digital accelerometer with very low self-noise, built for structural health monitoring, seismic sensing and precise tilt measurement.

Acceleration, tilt angle or both, with programmable filters and a synchronized trigger, so a monitoring node needs little extra signal processing.

0.2µg/√HzNoise density
±15gRange
460HzMax. bandwidth
3axesacceleration or tilt
13.2mAat 3.3 V
Applications

Where the M-A352AD10 fits best

Bridges and buildings

Ambient vibration, modal analysis and long-term monitoring of natural frequencies.

Railway infrastructure

Deflection and vibration of bridge girders under passing trains.

Tilt and inclination

Slope, wall and foundation monitoring with tilt output in microradians.

Seismic networks

Dense sensor networks where force-balance sensors would be too costly.

Proven

Proven in independent tests

Shake table study, Sensors (MDPI) 2025

On a scaled masonry building, the M-A352 had the lowest noise of the MEMS accelerometers tested.

Railway bridges, JR East

Epson, JR East and Nagano Keiki use the M-A352 in a device that measures the deflection of steel railway bridges.

All studies and articles

See the knowledge downloads →

Performance

Key specifications

ParameterTypical value
Axes3, digital output
Measurement range±15 g; tilt ±60°
Noise density0.2 µg/√Hz typ.
Bias stability0.2 µg (Allan variance)
BandwidthDC to 460 Hz, upper cutoff selectable
Output rate50 to 1000 Sps
Resolutionabout 0.06 µg/LSB
Filtersprogrammable FIR, moving average
InterfaceUART or SPI, external trigger
Supply3.3 V, 13.2 mA typ.
Operating temperature−30 … +85 °C
Size, weight48 × 24 × 16 mm, 25 g, aluminum case

Typical values from the Epson data sheet. The full data sheet is available on request.

M-A352AD10

Structural monitoring

Noise density0.2 µg/√Hz
Range±15 g
BandwidthDC–460 Hz
Low noise (relative)

M-A370AD10

Seismic grade

Noise density0.02 µg/√Hz
Range±10 g
BandwidthDC–210 Hz
Low noise (relative)

M-A342VD10

Machine vibration

Outputvelocity, displacement
Bandwidth10–1000 Hz
Range±100 mm/s
FAQ

Frequently asked questions

Why does self-noise matter for structural monitoring?

Ambient vibration of bridges and buildings is very small. A low noise floor lets you identify natural frequencies and mode shapes from ambient excitation, without shakers or traffic loads.

Can the M-A352AD10 output tilt directly?

Yes. It outputs acceleration, tilt angle or a combination, with tilt resolution in the microradian range.

How do I synchronize several sensors?

An external trigger input allows synchronized sampling across nodes, which is important for modal analysis.

When should I choose the M-A370AD10 instead?

The M-A370AD10 has a ten times lower noise floor (0.02 µg/√Hz) for seismology and very weak structural signals.

Available directly in our shop.For larger projects or a comparison with the M-A370AD10, we lend evaluation kits free of charge.

Specifications "Epson Accelerometer M-A352AD10 UART/SPI"
Bandwidth: DC … 460 Hz
Current Consumption: 13.2mA @ 3.3V
Detected Axis: 3 ( X/Y/Z )
Dimension: 48x24x16 mm3
Interface: UART/SPI
Noise Density: 0.2 µG/Hz
Operating Temperature (max): +85°C
Operating Temperature (min): -30°C
Output Data Rate: 1000Sps
Physical Output Format: Acceleration, Tilt Angle
Range (Accelerometer): +/- 15G
Resolution: 0.06 µG/LSB
Series/ Type: M-A352
Shock: 1000 G
Supply Voltage, Vcc: 3.3 V
Weight (g): 25 g
Datasheets
Briefsheet

Oops! Your browser doesn't support PDFs!

Download "Briefsheet" (344.70 KB)